Commercial Pool Filters
Commercial Pool Heaters
Commercial Starting Blocks
Request a free catalog

Home Pool Supplies Pool Pumps D Series

Commercial Pumps


D Series Commercial Pump

Please Click Here for an Image Gallery

Especially designed for commercial and public swimming pools and spas, aquatic facilities, water parks and fountain applications where high performance and self-priming characteistics are desired. These self-priming, high performance pumps are available in high head and medium head models, providing a complete range of performance characteristics. Motors are open drip-proof, continuous duty rated 3450 RPM.

  • NOTE: ALL PUMP MODELS require external overload protection. 3-phase models, and 5 HP single phase, require a magnetic starter.
  • NOTE: Maximum ambient temperature: 104 F (40 C).
  • NOTE: 200 and 575 volt models availabe.
  • NOTE: Pumps are NSF listed only when installed with hair and lint trap. PUMPS (and performance curves) DO NOT INCLUDE HAIR AND LINTTRAP.
  • 2", 21/2" or 3" suction port and 11/2", 2" or 21/2" discharge port.

Item No Description Freight List Price Price Save  
DMH3-171 D-Series 3 HP Commerical Pool Pump 230/460 3 Phase FREE $1,676.93 $1,117.95 $558.98
DMJ3-172 D-Series 5 HP Commerical Pool Pump 230/460 3 Phase FREE $1,771.43 $1,180.95 $590.48
DMH-171 D-Series 3 HP Commerical Pool Pump 230 V FREE CALL FOR PRICE
DMJ-172 D-Series 5 HP Commerical Pool Pump 230 V FREE $2,189.93 $1,459.95 $729.98

D series Ordering
D-Series Dimensions
D Series


D-series Curve



Recirculating pump shall be Sta-Rite model no. _______ self-priming
centrifugal pump, ____ phase, 60 Hz.

General Notes

• Install pump in a cool, dry, well vented location away from pool
heaters and chemical storage.

• Pump should be firmly mounted with pipe supported, to prevent vibration
and undue operational noise.

• Allow 12" minimum clearance behind motor for servicing.

• Motor overheating may be caused by a voltage drop or excessive voltage.
Be sure that wire size and voltage input is properly regulated.


• The recirculating pump shall be a self-priming centrifugal design with
a hair and lint strainer as shown in the plans.

• The pump body and seal plate shall be constructed of close-grained
gray iron and close-coupled to an electric motor by means of an
adaptor of the same material. The pump body shall have a single
suction port with a four-bolt flange connection to the hair and lint
strainer. A centerline discharge port of ____" NPT and a winterizing
drain port of 1/4" NPT shall be a part of the design.

• The pump shall be a back pull-out design to allow servicing without
disturbing piping. The pump shall have a cast iron diffuser to aid in
priming and it shall contain a replaceable bronze wear ring for
the impeller. The impeller shall be of the closed type and cast in red
brass, non-overloading at any point on the performance curve. The
mechanical shaft seal shall be a John Crane® type 2 or equivalent and
constructed of ceramic and carbon seal faces, with stainless steel,
brass and Buna N materials in the spring bellows portion. The
impeller shall be secured to the motor shaft by means of a stainless
steel key and locking screw into the end of the motor shaft. There
shall be a shaft slinger made of neoprene to protect motor bearings
from any seal leakage. The pump shall be capable of operating at up
to 75 psi, 200°F continuous water temperature and within a pH range
of 4 to 9.

Home Pool Supplies Pool Pumps D Series


small $3.99 to $7.99 handling fee per order

Order Amount Handling Fee
$0.01 - $24.99 $8.99
$25.01 - $100.00 $9.99
Over $100.00 $10.99
Pool Lifts
Safety Vacuum Release Systems
Skamper Ramp
Winter Inflatable Toys
SR Smith Splash Deck
We Accept
credit card
Swimming Pool Supplies | Swimming Pool Pumps | Swimming Pool Filters | Swimming Pool Heaters
Home | About Us | Site Map | Manufacturers | Links | Privacy Policy & Legal Notice
ęCopyright 2000-2014 All rights reserved. Logo

D Series - Commercial Swimming Pool Pump